LEDs are optoelectronic devices that make pn junctions from compound materials. It has the electrical properties of a pn junction device: IV, CV, and optical: spectral response, luminescence, directional, time, and thermal properties. This article will give you a detailed introduction.
1, LED electrical characteristics
1.1 IV characteristics
Characterize the main parameters of the LED chip pn junction preparation performance. The IV characteristics of LEDs have non-linear, rectifying properties: unidirectional conductivity, that is, the application of a positive bias exhibits low contact resistance, and vice versa.
As shown above:
(1) Positive dead zone: (Fig. oa or oa' segment) Point a is the turn-on voltage for V0. When V < Va, the applied electric field overcomes a lot of potential field due to carrier diffusion, and R is very Large; turn-on voltage is different for different LEDs, GaAs is 1V, red GaAsP is 1.2V, GaP is 1.8V, and GaN is 2.5V.
(2) Forward working area: current IF is exponential with applied voltage
IF = IS (e qVF/KT –1) -------------------------IS
Is the reverse saturation current. When V>0, the positive working area IF of V>VF rises with the VF index.
IF = IS e qVF/KT
(3) Reverse dead zone: When V<0, pn junction plus reverse bias voltage V= - VR, when reverse leakage current IR (V= -5V), GaP is 0V and GaN is 10uA.
(4) Reverse breakdown region V<- VR, VR is called reverse breakdown voltage; VR voltage corresponds to IR is reverse leakage current. When the reverse bias voltage is increased such that V < - VR, a sudden increase in IR occurs and a breakdown occurs. The reverse breakdown voltage VR of various LEDs is also different due to the type of compound material used.
1.2 CV characteristics
Since the LED chip has 9×9mil (250×250um), 10×10mil, 11×11mil (280×280um), 12×12mil (300×300um), the pn junction area is different, which makes the junction capacitance (zero). Bias) C≈n+pf or so. The CV characteristics are quadratic (see Figure 2). The 1 MHZ AC signal was measured with a CV characteristic tester.
Innosilicon Machine:Innosilicon A10 ETHMaster (500Mh),Innosilicon A10 Pro ETH (500Mh),Innosilicon A10 Pro+ ETH (750Mh),Innosilicon A11 Pro ETH (1500Mh)
Innosilicon is a worldwide one-stop provider of high-speed mixed signal IPs and ASIC customization with leading market shares in Asian-Pacific market for 10 consecutive years. Its IP has enabled billions of SoC's to enter mass production, covering nodes from 180nm to 5nm across the world`s foundries including: GlobalFoundries, TSMC, Samsung, SMIC, UMC and others. Backed by its 14 years of technical expertise in developing cutting-edge IPs and ASIC products, Innosilicon has assisted our valued partners including AMD, Microchip and Microsoft to name but a few, in realizing their product goals.
Innosilicon team is fully devoted to providing the world's most advanced IP and ASIC technologies, and has achieved stellar results. In 2018, Innosilicon was the first in the world to reach mass production of the performance-leading GDDR6 interface in our cryptographic GPU product. In 2019, Innosilicon announced the availability of the HDMI v2.1 IP supporting 4K/8K displays as well as our 32Gbps SerDes PHY. In 2020, we launched the INNOLINK Chiplet which allows massive amounts of low-latency data to pass seamlessly between smaller chips as if they were all on the same bus. With a wide range of performance leading IP in multiple FinFET processes and 22nm planar processes all entering mass production, Innosilicon's remarkable innovation capabilities have been proven in fields such as: high-performance computing, high-bandwidth memory, encrypted computing, AI cloud computing, and low-power IoT.
Innosilicon Machine,A11 Pro 1500M Miner,Asic Miner A11 Pro 8G,A11 Pro 8G 1500Mh,ETC miner
Shenzhen YLHM Technology Co., Ltd. , https://www.nbapgelectrical.com