Sc Fast Connector/Field Installable Assembly Connector

SC/APC Fast Connector /Field Installable Connector Assembly 

Fast fiber connector is used for field-installable optical fiber connector, widely used in Fiber To The Home (FTTH)
access optical networks, not only for single-mode or multimode fiber, and can also choose to 900um,3 mm and the
introduction of cable       buffered type. With fast installation time and low insertion loss, the connector system provides
a good alternative to fusion splicing. Installation is as easy as strip, clean, cleave cam and crimp.






A. Components                                       
1. Back cover open tool
2. Housing Body
3. Field installable Mini-MT ferrule                              
4. Small pieces               
5. Crimp eyelet
6. Protective shell

B. Tooling Kits
Shown at left:
1. Butterfly fiber optic cable crimpers
2. Mechanical stripper
3. Fixed-length cutting template
4. Back cover open tool                                       
5. Fiber cutting tool

C. Installation Instruction

Step1:Fiber optic cable stripping
  2,Use Mechanical stripper remove coating layer 0.25mm, leaving about 24mm;
3,Wipe the fiber with a piece of tissue (It's better to use alcohol).
4. Set cable length 32mm by cutting template, cut the fiber in length.

Step2:Fiber insertion and assembly

1. Open the back cover of the connector
housing, insert fiber in place.
2. Tilt cable 30-45°until it stopped by
clip of connector.
3. Promote the cable until the fiber from
housing slightly bending 2-3mm then
forward ,repeated twice.
4. Press fiber into the booth slot, ensure
   the fiber has slightly curved.
5. Close the back cover to ensure the reliable
   lock of the back cover on the sides.
6. Pull out the small piece of fiber.      
   
Step3:Assembly of the protective shell 

Product parameters

D. Reuse 
Step1:Remove the fiber optic connector protective shell
Step2:Use back cover tool to open the back cover of Housing   
Step3:Position the cover tool at the Housing of connector, push forward it to completely push the old fiber out
of connector Housing
Step4: Remove the existing fiber, insert a new fiber, and repeat the above-mentioned optical fiber positioning and fixed
steps to complete the assembly

FOR FURTHER INFORMATION,PLEASE LEAVE ME  MESSAGE !





  SC/APC Fast Connector /Field Installable Connector Assembly 

Fast fiber connector is used for field-installable optical fiber connector, widely used in Fiber To The Home (FTTH)
access optical networks, not only for single-mode or multimode fiber, and can also choose to 900um,3 mm and the
introduction of cable       buffered type. With fast installation time and low insertion loss, the connector system provides
a good alternative to fusion splicing. Installation is as easy as strip, clean, cleave cam and crimp.






A. Components                                       
1. Back cover open tool
2. Housing Body
3. Field installable Mini-MT ferrule                              
4. Small pieces               
5. Crimp eyelet
6. Protective shell

B. Tooling Kits
Shown at left:
1. Butterfly fiber optic cable crimpers
2. Mechanical stripper
3. Fixed-length cutting template
4. Back cover open tool                                       
5. Fiber cutting tool

C. Installation Instruction

Step1:Fiber optic cable stripping
  2,Use Mechanical stripper remove coating layer 0.25mm, leaving about 24mm;
3,Wipe the fiber with a piece of tissue (It's better to use alcohol).
4. Set cable length 32mm by cutting template, cut the fiber in length.

Step2:Fiber insertion and assembly

1. Open the back cover of the connector
housing, insert fiber in place.
2. Tilt cable 30-45°until it stopped by
clip of connector.
3. Promote the cable until the fiber from
housing slightly bending 2-3mm then
forward ,repeated twice.
4. Press fiber into the booth slot, ensure
   the fiber has slightly curved.
5. Close the back cover to ensure the reliable
   lock of the back cover on the sides.
6. Pull out the small piece of fiber.      
   
Step3:Assembly of the protective shell 

Product parameters

D. Reuse 
Step1:Remove the fiber optic connector protective shell
Step2:Use back cover tool to open the back cover of Housing   
Step3:Position the cover tool at the Housing of connector, push forward it to completely push the old fiber out
of connector Housing
Step4: Remove the existing fiber, insert a new fiber, and repeat the above-mentioned optical fiber positioning and fixed
steps to complete the assembly

FOR FURTHER INFORMATION,PLEASE LEAVE ME  MESSAGE !





 

Zov Varistor

Semiconductor Ceramic Component,Power Surge Protector Zinc Metal Oxide Varistor,Zinc Oxide Varistor

Film Capacitor,Ceramic Capacitor Co., Ltd. , http://www.nbxinqing.com